ENGLISH
ENGLISH
8
9
In case you want to postpone the time of cooking then before choosing any program press the
Button “Таймер отложенного старта” as many times as needed. The figures show the time of the
delay, for example, if you see “00:30” - it means that cooking will start in 30 minutes. The maximum
time setting is 24 hours.
Choose the menu according to different recipes
Press one of the Menu Buttons in relation to the kitchen-stuff you’re cooking (press “Рис” Button for
rice cooking, for example) and the indicator of this button lights up.
If necessary you can change the time of cooking with “Установка времени приготовления» button
after choosing the appropriate program button.
Note:
you should remember that the programmed time is approximate and you can specify it ac-
cording to your preferences.
Note:
in case the kitchen-stuff don’t belong to any group in the menu you should choose a similar
group.
The time of cooking (programmed)
This time is indicated after you chose the exact type of food button and means the time of cooking
after the pressure inside achieves working state. It doesn’t include the time until achieving working
pressure.
After time setting wait for some seconds and the process will start.
•
Pressure holding process begins when pressure inside is high enough.
•
When pressurizing is over, you’ll hear 3 sound signals, they indicate the end of cooking and the
start of keeping warm process.
•
Press Отмена/Поддержание тепла Button to cancel parameter setting or current working sta-
tus.
8. Take out the food in the following steps:
Turn the Relief Valve to “выпуск пара” position to release steam.
Note:
When cooking fluid food, such as porridge, to avoid squirting up remember not to release the
steam immediately after 3 sound signals. Let the pressure cooker cool down naturally or use the
cooling system. Otherwise the fluid food may squirt and result in damage.
•
Remove the plug form the socket.
•
Turn the Handle counter clockwise; open it and take the food out.
Attention!
When the food is ready and the function “keeping warm” is switched , the pressure inside is high, the
protection devices don’t let open the Lid immediately. In order to speed up cooling down you can use
the cooling system to cool it and make the pressure down soon, especially when the food is fluid.
•
Unplug the device.
•
Turn regulator of reduce the pressure to the “vent of steam”.
•
The lid will be unlocked when internal temperature and pressure are reduced.
STEAMER FUNCTION
The appliance can be used as a Steamer. For this purpose use a special accessory that you have
bought with the appliance – the Steamer .
•
Add some water (1/5 scale) into the Inner Pot. Put the Steamer with kitchen-stuff into the Inner
Pot and close the Lid.
•
Turn the Relief Valve to “Герметично” position.
•
Power on the appliance with the Power Cord.
•
Choose the button “Пароварка”.
•
Cooking time is up to your preferences – control the cooking time according to your food or
menu. For this use the “Установка времени” button.
•
Press the “Отмена/Поддержание тепла” button if you would like to stop the cooking process.
CLEANING
•
Remove the plug from the socket before cleaning wait until the appliance has normal tempera-
ture.
•
Take out the Inner Pot and clean it with a sponge or nonmetal soft brush, and then dry it with
towel.
•
Rub the Inner Surface of the appliance with a soft cloth.
•
Clean the outer coating of the appliance with a soft slightly wet towel. Never dip it in water for
cleaning or run water over it.
•
Take off the Water Collector and clean it with a wet towel. Put it back as shown in the picture:
•
Clean the Sealing Gasket, Relief Valve, and Floating Valve with soap water then dry them with a
towel. After cleaning put the parts together again.
Attention!
For your safety remember that when the appliance is on it must not contact with water
or other liquids especially the cord and the base of the appliance.
You must not dip the appliance into the water to avoid electric shock, fire or injuring.
Never wash the appliance in a dishwasher!
TROUBLESHOOTING
NO. A Problem
The Cause
The Solution
1
Difficult to close the Lid
The sealing gasket is not fixed
well
Fix the sealing gasket well
2
Difficult to open the Lid
The pressure inside is too high
Let the steam out turning the
relief valve left or right
3
Steam leaks off the Lid
There isn't a sealing gasket in
the Lid
Put the sealing gasket into
the Lid (see “Appliance use”
paragraph)
The sealing gasket isn't clean
Clean the Sealing Gasket
The sealing gasket is damaged
or deformed
Change a broken or de-
formed Sealing Gasket to a
new one in a UNIT service
center
The Lid isn't fixed properly
Fix the Lid properly
4
Indicating lights are not
on
The appliance isn't powered on Check the power cord and
the plug
Some other problems
Send the appliance to a UNIT
service center
5
E1
Open circuit of the sensor
Send the appliance to a UNIT
service center
E2
Short circuit of the sensor
E3
Over-temperature
E4
Disable signal switch
E5
The lid is not covered well
Cover the lid well
SPECIFICATIONS
Model
Rated Volt-
age
Power
Capacity
Diameter
Working
Pressure
USP-1080D
220-240 V,
50 Hz
1000 W
6 L
22 cm
0-70 kPa
