1 FM ANTENNA TERMINAL
•
Connect the supplied wire “dipole” FM antenna to the FM antenna
terminal using the supplied “balun” adapter. It will usually work best
when mounted on a vertical surface such as a wall, with arms fully
outstretched forming a horizontal “T” perpendicular to the origin
point of the signal.
AM ANTENNA TERMINAL
The AM loop antenna supplied with the C 446 (or a suitable
replacement) is required for AM reception.
•
Connect the supplied AM loop antenna to these terminals. If an
external AM antenna is used, make connections to the AM and GND
terminals in accordance with the instructions supplied with the
antenna.
•
Testing different positions for the antenna may improve reception;
vertical orientation will usually produce the best results. Antenna
proximity to large metal objects (appliances, radiators) may impair
reception, as well as attempts to lengthen the wire to the loop.
•
Refer also to the item about ASSEMBLING THE LOOP ANTENNA at
the LISTENING TO AM/FM RADIO section of the OPERATION page.
2 DAB ANTENNA TERMINAL (230V version model only)
•
Install the supplied DAB antenna into this DAB terminal.
•
With DAB, you can receive CD-like quality programs without any
annoying interference and signal distortion.
•
Refer also to the “LISTENING TO DAB RADIO” segment of the
“OPERATION” section.
3 AUDIO OUT
Connect to the corresponding analog audio input of an amplifier,
receiver or stereo system.
4 DIGITAL OUT
Using an optical cable (TOSLINK connector), connect DIGITAL OUT to
the corresponding digital audio input of receivers or digital processors.
5 LOCAL AREA NETWORK (LAN) PORT
•
LAN connection must be setup for Wired connection to be
established. Set up a Wired Ethernet broadband router with
broadband internet connection.
•
Using a standard straight-through Ethernet cable (not supplied),
connect one end of the Ethernet cable to the LAN port of your wired
Ethernet broadband router and the other end to C 446’s LAN port.
NOTES
•
NAD is not responsible for any malfunction of the C 446 and/or the
internet connection due to communication errors or malfunctions
associated with your broadband internet connection or other connected
equipment. Contact your Internet Service Provider (ISP) for assistance or
the service bureau of your other equipment.
•
Contact your ISP for policies, charges, content restrictions, service
limitations, bandwidth, repair and other related issues pertinent to
internet connectivity.
6 WIRELESS (WIFI) ANTENNA TERMINAL
•
Install the supplied wireless antenna into this wireless antenna
terminal (WiFi).
•
Wireless (WiFi) broadband router with broadband internet
connection is required for wireless connection to be established.
7 RS 232
NAD is a certified partner of AMX and Crestron and fully supports
these external devices. Check out the NAD website for information
about AMX and Crestron compatibility with NAD. See your NAD audio
specialist for more information.
•
Connect this interface using RS-232 serial cable (not supplied) to
any Windows compatible PC to allow remote control of the C 446
via compatible external controllers.
8 MP DOCK
The C 446 is equipped with a data port in the rear panel where an
optional NAD IPD (NAD IPD Dock for iPod) 1, NAD IPD 2 and later
variants can be plugged in.
•
Connect the “MP DOCK (DATA PORT)” jack of the C 446 to the
corresponding “DATA PORT” socket of the optional NAD IPD model.
•
Connection between the C 446 and NAD IPD is only via their
respective DATA PORT. NAD IPD audio and S-Video port connections
should be directed to the external device’s corresponding input
ports (assigned for NAD IPD).
NOTE
The NAD IPD Dock for iPod is not supplied with your C 446.
IDENTIFICATION OF CONTROLS
REAR PANEL
© NAD C 446
FM
ANTENNA
GND
AM
DAB
AUDIO OUT
DIGITAL OUT
LAN
RS232
MP DOCK
+12V
TRIGGER
IN
POWER
100~240V – 50/60Hz
ON
IR IN
DATA PORT
L
R
WIFI
3
4
5
6
7
8
9
11
10
1
2
12
ATTENTION!
Please make sure that the C 446 is powered off or unplugged from the mains power source before making any connections. It is also advisable to power down
or unplug all associated components while making or breaking any signal or AC power connections.
7
ENGLISH
POR
TUGUÊS
FR
ANÇ
AIS
ESP
AÑOL
IT
ALIANO
DEUT
SCH
NEDERL
ANDS
SVENSK
A
РУ
ССКИЙ
