Press the right rotary control to con
fi
rm the selected setting.
By selecting “EXIT” and then pressing the right rotary control you move up one menu level: from
the selected setting to “SETTINGS” to the main menu.
3.1. Setting the appliance for use with or without
fi
lter
To adjust the mode turn the right rotary control in the main menu to “SETTINGS” and press it.
Select “FILTER” from menu “SETTINGS” by turning the right rotary control.
Using the appliance
with
fi
lter: please follow the procedure in 2.4.1.
Using the appliance
without
fi
lter: please follow the procedure in 2.4.2.
You can adjust the other settings directly from here or leave the menu by choosing “EXIT” and
then press the right rotary control.
3.2. Setting the water hardness level
To adjust the water hardness turn the right rotary control in the main menu to the “SETTINGS”
menu and then press it.
Enter “SETTINGS” and select “WATER HARDNESS” by pressing the right rotary control.
Then follow the procedure in 2.4.3
You can adjust the other settings directly from here or leave the menu by choosing “EXIT” and
then press the right rotary control.
3.3. Adjusting the temperature
You can adjust the temperature as required for coffee, milk and hot water to “NORMAL”, “HIGH”,
“MAXIMUM” or “INDIVIDUAL”. The ex-factory setting is “HIGH”. If the temperature has been adjusted
as outlined below this applies to all coffee varieties.
You can however set the temperature for each coffee speciality as “INDIVIDUAL” (see 4. below.)
Adjust the temperature settings in the “INDIVIDUAL” menu as follows:
Turn the right rotary control in the main menu to “SETTINGS” and press it.
Turn the right rotary control to “TEMPERATURE” and press it.
Turn the right rotary control to “INDIVIDUAL”.
Press the right rotary control to con
fi
rm your setting.
You can adjust the other settings directly from here or leave the menu by choosing “EXIT” and
then press the right rotary control.
3.4. Adjusting the aroma
(not model 758)
You can adjust the aroma of your coffee according to taste. To do so, use one of the three pro
fi
les for
varying water pressure in the “AROMA” menu. The “DYNAMIC” pro
fi
le delivers dynamic percolation,
“CONSTANT” stands for a constant and “INTENSE” for an intense percolation. The ex-factory setting
is “INDIVIDUAL”, which means that you can select your preferred aroma selection for each coffee
recipe. Should you however opt for a pre-select aroma pro
fi
le of 1,2 or 3, this will be applied to all
coffee specialities.
Tip: Test your preferred aroma selection on one drink.
To change the aroma settings turn the right rotary control in the main menu to “SETTINGS” and
then press it.
Turn the right rotary control to “AROMA“ and press it.
Turn the right rotary control to select the aroma pro
fi
le of your choice.
Press the right rotary control to con
fi
rm your choice.
You can adjust the other settings directly from here or leave the menu by choosing “EXIT” and
then press the right rotary control.
3.5. Select language
To change the language turn the right rotary control in the main menu to “SETTINGS” and press it.
In “SETTINGS” turn the right rotary control to “LANGUAGE” and press it.
By turning the right rotary control you change the language.
Press the right rotary control to con
fi
rm the chosen language.
You can adjust the other settings directly from here or leave the menu by choosing “EXIT” and
then press the right rotary control.
3.6. Set automatic switch-off time
This function allows you to determine the automatic switch-off time after the last use. The ex-factory
setting is after “10 MINUTES”.
To change settings turn the right rotary control in the main menu to “SETTINGS” and press it.
Turn the right rotary control to “APPLIANCE AUTO-OFF” and press it.
The display shows the possible switch-off times.
Turn the right rotary control to the requested selection.
Press the right rotary control to con
fi
rm your choice.
Your appliance will now automatically shut down after use according to the switch-off time.
You can adjust the other settings directly from here or leave the menu by choosing “EXIT” and
then press the right rotary control.
3.7. Switch-off rinsing
Ex-factory the
automatic switch-on
rinsing function is permanently installed. Every time the appliance
is switched on after an inactive state, it will heat the water up and ask for a rinse to ensure that fresh
water is always used.
This request is shown in the display and needs to be started manually by pressing the right rotary control.
Ex-factory the
switch-off
rinsing is set on “
ON
”.
Optionally the automatic switch-off rinsing function can be de-activated after the appliance has been
switched off:
Turn the right rotary control in the main menu to “SETTINGS” and press it.
Turn the right rotary control to “SWITCH-OFF RINSING” and press it.
Turn the right rotary control to “ON” or “OFF” and press it.
The display shows the other optional settings.
You can adjust the other settings directly from here or leave the menu by choosing “EXIT” and
then press the right rotary control.
Note: Even if the switch-off rinse is set on “ON”, it will only be performed if at least one drink has been
prepared.
3.8. Factory settings
All changes made in the settings and all recipes can be reset in “FACTORY SETTINGS”.
Turn the right rotary control in the main menu to “SETTINGS” and press it.
Turn the right rotary control to “FACTORY SETTINGS” and press it.
Turn the right rotary control to “RESET RECIPES” or “RESET SETTINGS”.
Press the right rotary control to con
fi
rm.
You can adjust the other settings directly from here or leave the menu by choosing “EXIT” and
then press the right rotary control.
3.9. View statistics
The menu item “STATISTICS” details how many drinks and functions have been prepared/used since
72
73
GB
GB
3. Setting/adjusting basic settings
3. Setting/adjusting basic settings
