10
11
EN
EN
•
Strength of ready coffee depends on the quality and
grinding degree of coffee beans.
•
If coffee is pouring out too long, this means the
coffee powder is too fine it is tamped too strongly; in
this case use coarse-ground coffee and choose the
tamping degree experimentally.
MAKING ESPRESSO
ATTENTION!
Do not remove the filter holder (18) during making
coffee.
Do not remove the filter holder (18) right after
making coffee, as there is redundant pressure
inside, wait a little before removing the filter holder
(18).
• Remove the lid (9), remove the water tank (10).
• Fill the tank (10) with cold water, do not exceed the
maximal level mark, install the tank (10) back to its
place.
•
Install one of the coffee filters (19 or 20), depending
on the amount of ready coffee, into the filter holder
(18) matching the ledge on the filter (19 or 20) with
the hole on the holder (18) and turn the filter (19 or
20) counter/clockwise.
•
Add the required amount of ground coffee into the
filter (19 or 20) with a measuring spoon (21) and
slightly tamp the coffee in the filter (19 or 20) with the
back side of the measuring spoon (21) (pic. 5, 6, 7).
•
Install the filter holder (18) into the installation place «
» and turn the handle (4) to the right as far as it will go
« » (pic. 2, 3, 4).
• Place a cup of suitable height and capacity (see the table
CHOOSING THE APPROPRIATE CUP) on the grid (2); if
you use small cups, take the pullout tray (3) by the lower
part and pull it towards yourself, place the cups on it.
• Insert the power plug into the mains socket.
•
Switch the coffee maker on by setting the power switch
(11) «0/I» to the position «I», the indicator (6) will light up
and start flashing.
•
When the coffee maker is ready for operation, the light
indicator (6) will glow constantly.
•
To make one cup of espresso, use the small filter (19)
and press the «Espresso»-button (5) once; the light
indicator « » will light up.
•
To make two cups of espresso, use the larger filter (20)
and press the «Espresso»-button (5) twice; the light
indicator « » will light up. In this case set one big or
two small cups on the grid (2 or 3).
Notes:
- if you need to switch the coffee maker off during the
espresso making, press the «Espresso»-button (5) again;
– successive making of coffee should be performed with
intervals 2-3 min.
• Remove the cup with ready drink from the grid (2 or 3).
•
After you finish using the coffee maker, switch the coffee
maker off by setting the switch (11) «0/I» to the position
«0».
•
Wait until the coffee maker cools down, remove the
filter holder (18) and wash the installed filter (19 or 20).
ESPRESSO PORTION SETTING
• During making espresso press and hold the button (5)
for 3 seconds. When the cup is filled with necessary
amount of espresso, press the button (5) again.
• Next time when you make espresso, the preset amount
of ready coffee will be poured into the cup.
Notes:
- minimal and maximal amount of espresso are specified
in the table «CHOOSING THE APPROPRIATE CUP»;
- if you need to make a lesser amount of coffee then it was
set, press the button (5) again when the cup is filled with
necessary amount of ready coffee.
Return to the factory settings
•
To return to the factory settings switch the coffee maker
off by setting the switch (11) «0/I» to the position «0».
• Press and hold the «Espresso»-button (5) and switch
the coffee maker off by setting the power switch (8)
«0/I» to the position «I».
•
The coffee maker is ready for operation with the factory
settings.
MAKING CAPPUCCINO
ATTENTION! When making cappuccino be careful to
avoid burns by outgoing hot steam.
• Make sure that the removable tray (1) and the tray grid
(2) are installed to their places.
• Fill the tank (10) with cold water, do not exceed the
maximal level mark, install the tank (10) back to its
place.
• Take the container (16), pull it towards yourself and
remove it (pic. 1), remove the cappuccinator lid (14)
from the container (16).
• Fill the container (16) with milk, do not exceed the
maximal level mark.
• Install the cappuccinator lid (14) on the container (16)
and install the cappuccinator back to the installation
place until the lock clicking.
•
Install one of the coffee filters (19 or 20) into the filter
holder (18) matching the ledge on the filter (19 or 20)
with the hole on the holder (18) and turn the filter (19 or
20) counter/clockwise.
•
Add the required amount of ground coffee into the filter
(19 or 20) with a measuring spoon (21) and slightly
tamp the coffee in the filter (19 or 20) with the back side
of the measuring spoon (21) (pic. 5, 6, 7).
•
Install the filter holder (18) into the installation place «
» and turn the handle (4) to the right as far as it will go «
» (pic. 2, 3, 4).
