8
9
EN
EN
•
Disconnect the power plug from the mains socket
and wait until the iron soleplate (11) cools down
completely.
Note:
when switching the unit on for the first time,
foreign smell can appear. It is normal.
STEAM IRONING
The iron is equipped with anti-drip valve that stops water
supply, if the soleplate (11) temperature is too low, it
prevents dripping from the soleplate (11) openings.
Steam ironing is possible only if the temperature control
knob (12) is set to the steam mode «•••» or «MAX».
•
Place the iron on its base (9).
•
Insert the power plug into the mains socket.
•
Make sure that there is enough water in the water
tank (10).
•
Turn the control knob (12) to set the required ironing
temperature in the steam mode «•••» or «MAX», the
indicator (6) will light up.
•
When the temperature of the soleplate (11) reaches
the set point, the indicator (6) will go out and you can
start ironing.
•
Set the necessary steam intensity with the continuous
steam supply knob (3): steam will be released from
the openings of the soleplate (11) only if the iron is in
horizontal position. To stop the steam supply, put the
iron vertically or set the knob (3) to the position « »
(steam supply is off).
•
After you finish ironing, set the temperature control
knob (12) to the position «OFF», and the continuous
steam supply knob (3) to the position « » (steam
supply is off).
•
Disconnect the power plug from the mains socket
and wait until the iron soleplate (11) cools down
completely.
ATTENTION!
If steam is not supplied during the operation, check
whether the temperature control knob (12) and the
steam supply knob (3) are set properly and whether
there is water in the water tank (10).
WATER SPRAY
•
Make sure that there is enough water in the water
tank (10).
•
Press the water spray button (5) to dampen the
fabrics.
BURST OF STEAM
•
The burst of steam is useful for ironing folds and can
be used only in the high temperature ironing mode;
set the temperature control knob (12) to the position
«•••» or «MAX».
•
When pressing the burst of steam button (4) steam
will go out of the iron soleplate (11) openings
intensively.
Note:
to avoid water leakage from the soleplate (11)
openings, press the burst of steam button (4) with 4-5
sec. intervals.
VERTICAL STEAMING
•
Vertical steaming of fabrics or interior objects can be
performed only in the high temperature ironing mode.
Set the temperature control knob (12) to the position
«•••» or «MAX»).
•
Hold the iron vertically at the distance of 5-20 cm
from the clothes or interior objects and press the
burst of steam button (4) with 4-5 second intervals,
steam will be released from the soleplate (11)
openings intensively.
ATTENTION!
- To avoid fabric melting, do not touch it with the iron
soleplate (11) while steaming.
- Do not steam clothes on a person. Use a clothes
hanger or a coat rack.
•
After you finish ironing, switch the iron off and
unplug it, wait until the iron soleplate (11) cools down
completely, then open the water inlet lid (2), turn over
the iron and drain the remaining water.
STEAM CHAMBER CLEANING
•
Regularly clean the steam chamber of the iron,
especially in the regions with «hard» tap water.
•
Set the continuous steam supply knob (3) to the
position « » (steam supply is off).
•
Open the lid (2), fill the tank with water up to the
maximal mark «МАХ» and close the lid (2).
•
Place the iron on its base (9).
•
Insert the power plug into the mains socket.
•
Set the temperature control knob (12) to the «MAX»
position, the indicator (6) will light up.
•
When the iron soleplate (11) reaches the set
temperature, the indicator (6) will go out and you can
start cleaning the steam chamber of the iron.
•
Remove the power plug from the mains socket.
•
Hold the iron above the sink horizontally, press and
hold down the button (13) «Self -Clean».
•
Boiling water and steam with scale will be intensively
released from the soleplate (11) openings.
•
Slightly sway the iron back and forth, until all the
water leaves the water tank (10).
•
Place the iron on its base (9) and let the soleplate
(11) cool down completely.
•
After the soleplate (11) cools down, wipe it with a dry
cloth.
•
Before taking the iron away for storage make
sure that the water tank (10) is empty, andthe iron
soleplate (11) is dry.
CLEANING AND MAINTENANCE
•
Before cleaning make sure that the iron is switched
off and cold and the power plug is not connected to
the mains socket.
•
Wipe the iron body with a slightly damp cloth and
