8
9
EN
EN
released from the openings of the soleplate (11) only
if the iron is in horizontal position. To stop the steam
supply, put the iron vertically or set the knob (3) to the
position « » (steam supply is off).
•
After you finish ironing, set the continuous steam
supply knob (3) to the position « » (steam supply
is off).
•
Disconnect the power plug from the mains socket
and wait until the iron soleplate (11) cools down
completely.
ATTENTION!
If steam is not supplied during the operation, check
whether the steam supply knob (3) are set properly and
whether there is water in the water tank (10).
Note:
- if you are going to iron delicate fabrics after the
soleplate (11) heats up, it is recommended to wait for
the next cycle of the indicator (6) switching off.
WATER SPRAY
•
Make sure that there is enough water in the water
tank (10).
•
Press the water spray button (5) to dampen the
fabrics.
BURST OF STEAM
•
The burst of steam is useful for ironing folds.
•
When pressing the burst of steam button (4) steam
will go out of the iron soleplate (11) openings
intensively.
Note:
to avoid water leakage from the soleplate (11)
openings, press the burst of steam button (4) with 4-5
sec. intervals.
VERTICAL STEAMING
•
Hold the iron vertically at the distance of 5-20 cm
from the clothes or interior objects and press the
burst of steam button (4) with 4-5 second intervals,
steam will be released from the soleplate (11)
openings intensively.
ATTENTION!
- To avoid fabric melting, do not touch it with the iron
soleplate (11) while steaming.
- Do not steam clothes on a person. Use a clothes
hanger or a coat rack.
•
After you finish ironing, switch the iron off and
unplug it, wait until the iron soleplate (11) cools down
completely, then open the water inlet lid (2), turn over
the iron and drain the remaining water.
AUTOMATIC SWITCH OFF
•
The iron has 2 automatic switch off modes.
1. If the iron is set in horizontal position and remains
still for 30 seconds, the iron’s heating element will be
switched off, and the indicator (6) will be flashing.
2. If you set the iron in vertical position on the base
(9) and leave it for 8 minutes, the heating element will
switch off and the indicator (6) will be flashing.
•
To resume ironing set the iron from horizontal
position to vertical or vice versa, wait until the iron
soleplate (11) heats up and continue ironing.
STEAM CHAMBER CLEANING
•
Regularly clean the steam chamber of the iron,
especially in the regions with «hard» tap water.
•
Set the continuous steam supply knob (3) to the
position « » (steam supply is off).
•
Open the lid (2), fill the tank with water up to the
maximal mark «МАХ» and close the lid (2).
•
Place the iron on its base (9).
•
Insert the power plug into the mains socket, the
indicator (6) will light up.
•
When the iron soleplate (11) reaches the set
temperature, the indicator (6) will go out and you can
start cleaning the steam chamber of the iron.
•
Remove the power plug from the mains socket.
•
Hold the iron above the sink horizontally, press and
hold down the button (12) «Self -Clean».
•
Boiling water and steam with scale will be intensively
released from the soleplate (11) openings.
•
Slightly sway the iron back and forth, until all the
water leaves the water tank (10).
•
Place the iron on its base (9) and let the soleplate
(11) cool down completely.
•
After the soleplate (11) cools down, wipe it with a dry
cloth.
•
Before taking the iron away for storage make
sure that the water tank (10) is empty, andthe iron
soleplate (11) is dry.
CLEANING AND MAINTENANCE
•
Before cleaning make sure that the iron is switched
off and cold and the power plug is not connected to
the mains socket.
•
Wipe the iron body with a slightly damp cloth and
then wipe it dry.
•
You can remove the mineral deposit from the iron
soleplate (11) with a cloth soaked in table vinegar.
•
•After removing the mineral deposit polish the
soleplate (11) surface with a dry clean cloth.
•
Do not use abrasives or solvents to clean the iron
soleplate (11) and body.
•
Avoid contact of the iron soleplate (11) with sharp
metal objects, as well as with metal buttons, zippers
etc.
•
Do not immerse the iron, the power cord and the
power plug into water or any other liquids.
STORAGE
•
Before taking the iron away for storage drain the
remaining water from the water tank (10) and clean
the iron.
•
Set the continuous steam supply knob (3) to the
position « » (the steam supply is off).
