FALMEC Eolo Isola 45 (450) E.ion ECP инструкция по эксплуатации онлайн - страница 20


Инструкция FALMEC Eolo Isola 45 (450) E.ion ECP для устройства вытяжка содержит страницы на русском языке.

Размер файла: 1.15 MB. Состоит из 68 стр.


Вы можете скачать pdf файл этой инструкции: Скачать PDF


Предыдущая
Следующая
background image

18

3) Connect the power supply cable (CAI) to the power supply clamp (MA) complying with the 

live, neutral and earth requirements (refer to sec. D).

(Fig. B)

1) Fasten the bracket (SC) to the ceiling using the 4 ø 8 fischer screws and relative V1 screws.
2) Insert the stainless steel lanyards (C) into the holes of the bracket cover plate (C).

(Fig. C)

1) Identify the height (Y) of the hood from the ceiling considering a height of X=60÷65 cm and 

that (Z) varies in accordance with the hood model. It is recommended to keep the height 
of Y> = 50-60 cm.

(Fig. D)

1) After having determined the height (Y), cut the excess steel lanyards (C1) in the lower 

part. 

2) Loosen the cable lock (BC) rotating the knurled cylinder anticlockwise;
3) insert the steel lanyards (C1) inside them;
4) lock them rotating the knurled cylinder clockwise after having rechecked that the hood is 

at the desired height “Y”.  Use a spirit level to check the hood in both directions.

5-6) Insert the hood power cable (CA) in the specific hole of the bracket cover plate (C) and 

connect it to the clamp (MA) complying with the provisions in sec. D. Lock the cable (CA) 
using the cable gland (P) pre-mounted on the bracket (SC).

(Fig. E)

1) lift the bracket cover plate (C)
2) screw the bracket cover plate (C) to the bracket (SC) using 2 screws (V4). 
3. Power the hood.

L2   INSTRUCTIONS FOR HOOD INSTALLATION WITH WALL BRACKET

(Fig. A)

1)  Cut off the voltage from the electrical system that powers the hood. Make sure there is a 

set-up for the electrical power supply (Solution A or B) for the hood on the wall it is being 
installed on, according to regulations in force.

2)  Position the hood bracket (SP) at distance Y, considering that the distance between the hood 

and cooking surface must be approximately 60-65 cm. 

3)  Attach the hood bracket (SP) using 2 Ø 8 mm dowels and relative V1 screws. Warning, if the 

power supply cable for the hood system (CAI) is positioned behind the hood bracket (SP) 
(Solution A), pass it through the hole (F) on the bracket.

(Fig. B)

1A)

 Solution A -> 

-  Momentarily place the hood near the hood bracket (SP) and connect the power supply 

clamp (MA) to the power supply cable of the hood (CA), observing the phase, neutral and 
earth requirements (see sec. D), cutting off any excess cable.

-  Place the clamp and the power supply cable between the back of the hood and the hood 

bracket (SP) so that they are hidden.

1B)

 Solution B (more common) -> 

 

the electrical outlet (PE) is placed near the hood. In this case it is necessary to install a plug 
with a phase, neutral and earth on the hood power supply cable (CA), observing the regula-
tions in force.

(Fig. C)

1)  Insert the heads of the V4 screws assembled on the hood into the holes on the hood bracket 

(SP).

2)  Move the hood so that the heads of the screws fit into the slots on the hood bracket.
3-4) Permanently fasten the bracket (SP) to the hood using the 4 V5 screws provided.  

(only for Solution B) 

Connect the hood to the electrical power mains.

-  Electrically power the hood.


Что удобнее для чтения книг?

Планшет
Электронная книга
Смартфон
Книга в бумажном переплёте
Не читаю книг

QR код manualbase.ru
©  2010- ManualBase.ru