USER'S GUIDE
GUÍA DE USUARIO
ENGLISH
Before 1st use
Connecting your phone:
- Connect plugs in corresponding sockets in the base station.
Plug the telephone line into telephone socket and insert power
plug in an electrical outlet.
- Insert batteries in handset.
Before you start to use your telephone, charge the AAA batteries
continuously for 15 hours.
Only use plug adapter supplied with the unit and
rechargeable batteries with your phone.
What the icons means?
Phone Function Keys
1
OK key
2
Back / Clear key
3
Navigation key
4
Talk key
- (Handsfree E192 only)
5
Hang-up / Exit key
6
Recall (Flash) key
- Access to operator service*
7
Menu key
8
Redial Key
9
Start key
10
Hash key
- To lock or unlock / to toggle between the external and
internal calls when both are set up.
11
Mute key
12
Call transfer/Intercom key
Fast blink indicates battery low.
.
Indicates that an external call is connected or held.
Icon blinks when receiving an incoming call.
Indicates you have a new voice mail message*.
Indicates you have new missed calls*, or the call log is being
viewed.
Displays when the phonebook is accessed.
Displays when the alarm clock is activated.
Displays when handsfree is activated (E192 only).
Displays when ringer volume is turned off.
Indicates that the handset is registered and within range of the
base station.
Icon blinks when the handset is out of range or is searching for a
base.
Displays menu mode to confirm your selection.
Indicates that more options are available.
Use the UP / DOWN keys to scroll up / down.
Displays menu mode.
Select BACK to return to the previous menu level.
Your Telephone Operations
Switching on / off
- Press and hold the key.
Notes: When the handset is OFF, it cannot be used for making calls
including emergency calls. There will be no ringing during an
incoming call.
To answer a call, you will need to switch it back on. It may take
some time for the handset to re-establish a radio link with the base
unit.
To lock / unlock the keypad
- Press and hold the
key.
Note: Incoming calls can still be answered even if the keypad was
locked.
SAFETY
This telephone is not designed for Emergency calls when the main
power fails.
Do not use your telephone to notify a gas leak or other potential
explosion hazard!
Do not open your device or its power supply to avoid risk of
electrical shock. Do not attempt to open the batteries, as they
contain hazardous chemical substances.
Your telephone must be located in a dry place away from hot,
humide and direct sunlight condition. To avoid radio signal
interference, place the phone at least 1 meter away from other
electrical appliances or other phones.
ENVIRONMENT
This symbol means that your inoperative electronic
appliance must be collected separately and not mixed
with the household waste.
Help us protect the environment in which we live!
Paging
-
Press located at the back of the base station. All the registered
handsets start to ring.
- Once retrieved, press any key on the handset or the again to
end the paging.
Call waiting
If you have subscribed to Call Waiting service, the earpiece will emit
a beep tone to inform you that there is a second incoming call.
The number or name of the second caller will also be displayed on
your phone if you have subscribed to Caller Line Identification
service (CLI). Please contact your network provider for more
information on this service.
Phonebook settings: 50 entries
Store a contact in the phonebook
- / or to select
PHONEBOOK
/ / to enter
NEW
ENTRY
/ enter the name of contact / / enter the number of
contact / / confirmation beep ( to delete characters).
Access phonebook
-
or to select
PHONEBOOK
/ / or to select
LIST
/ .
Note: Instead of pressing or to browse the phonebook
entries, you can press the numeric key corresponding to the first
letter of the entry you wish to locate.
Modify a phonebook entry
- / or to select
PHONEBOOK
/ / or to select
EDIT
ENTRY
/ / or to select an entry to edit / / current name
is displayed / edit the name / / edit the number / / confirmation
beep.
Delete a phonebook entry
-
/ or to select
PHONEBOOK
/ / or to select
DELETE
/ / or to select entry to delete / / /
confirmation beep.
Change the display language
- / or to select
AJUSTES PERS
/ / or to select
IDIOMA
/ / or to your desired language / /
beep.
confirmation
Note: Once the display language is set, the option menus on the
handset will switch to display in the selected language immediately.
Add / edit direct access memory
- /
or to select
PHONEBOOK
/ / or to select
DIRECT MEM.
/ / or to select
KEY 1
or
KEY 2
/ / stored
name displayed, or
NO NUMBER
displayed if it is empty / to
Using the call log: stored up to 10 external calls
Access call log
- /
or
/ .
Save call list entry into the phonebook
-
/ or to select an entry / / or to select
SAVE
NUMBER
/ to select and enter the name of contact (maximum
12 characters) / .
Delete a Call Log entry
-
/ or / / or to select
DELETE
/ / /
confirmation beep.
Delete all entries in the Call Log
-
/ / or to select
DELETE ALL
/ / / confirmation
beep.
Save a redial number into the phonebook
-
/ or to select an entry / to display
SAVE NUMBER
/ to display
ENTER NAME
/ enter the name of contact
(maximum 12 characters) / / return the display to redial list.
Delete direct access memory
-
/ or to select
PHONEBOOK
/ / or to select
DIRECT MEM.
/ / or to select
KEY 1
or
KEY 2
/ / stored
name displayed (or
NO NUMBER
if it is empty) / to enter direct
memory menu / or to select
DELETE
/ / / confirmation
beep.
Using the redial list
The redial list stores the last 5 numbers dialed.
Access redial list
-
/ or to browse the redial list / to view details.
Troubleshooting
If you have difficulty with your phone, please try the suggestions
listed below.
As a general rule, if a problem occurs, remove the batteries
from all the handsets in your installation for about 1 minute,
then disconnect and reconnect the power supply to the base
and reinstall the handset batteries.
Always
check first
that
:
Everyday use
“I cannot make or
answer calls”
You have followed all the steps listed in the user
manual to install and set up your telephone.
All connectors are firmly inserted in their sockets.
Mains power to the base unit is switched on at the
socket.
The handset’s batteries are correctly and securely
installed and are not run down.
If the handset’s display is blank, it may have been
switched off. Press and hold the HANG-UP/EXIT
key to switch it back on.
Check that the base unit’s mains power adapter is
plugged in and power is switched on.
The base unit needs mains power for normal
operation of the phone - not just for charging the
batteries.
Make sure you are using the telephone line cable
supplied with your telephone.
Other telephone line cables might not work.
Move the handset closer to the base unit.
Check the battery level symbol on the display. If it is
low, replace the handset on the base unit or charger
pod to recharge the batteries.
Switch off power at the mains socket, wait for a
short time and then switch back on. This may solve
the problem.
Batteries
“The handset’s
battery cells are
running low within
an hour or two”
“I try to recharge the
batteries but I still
get a warning that
they are low”
If the fault persists...
Before you first use the handset, you should have
left it on the base unit or charger pod for 15 hours
to charge the batteries fully. You may need to
replace the batteries. Check the connection
between the base unit and the mains power socket
unit.
You need to replace the batteries.
Dispose of used batteries safely – never burn them,
or put them where they could get punctured. Do not
use non - rechargeable batteries in your handset –
they may explode, causing damage.
Disconnect all other instruments connected to the
same line and try to make a call.
Disconnect the base unit from the telephone line
and plug a different phone into the master
telephone socket.
Try making a call. If this works, the line is OK.
If the call does not work, and you are using a two-
way socket adapter, remove it and plug a telephone
directly into the socket.
If the call now works, the adapter may be faulty.
If you cannot make a call, the fault may be on the
exchange line.
Contact the service provider.
“When I press on
the keys, nothing
happens”
“When I key in a
number, it appears
on the display, but I
cannot make an
outside call”
“The phone does
not ring”
“I hear ‘beeps’ from
my handset while
I’m on a call”
“When I try to make
a call, I hear busy
tone”
“The volume in the
earpiece is low
when I’m on a call”
Make sure the batteries are fitted in your handset
.
If the Battery Level symbol on the display shows
‘low’, put your handset back on the cradle to charge.
Try a different position for the base unit –
somewhere higher if possible, or further from other
electrical equipment.
Try moving the handset closer to the base unit.
Check that the base unit’s mains power adapter is
plugged in and power is switched on.
Check that ring volume is not on OFF.
You may be going out of range of the base unit.
Move closer or your call may be cut off.
Check the Battery Level symbol on the display.
If it’s low, recharge the batteries.
If you’re using a multi-handset system, check
whether another handset is already on a call.
Make sure you’re holding the earpiece correctly
over your ear.
Adjust the volume using the UP/DOWN key.
“I cannot make a
call”
If the handset display shows KEYS LOCKED, press
and
hold the * button to unlock it before you make
a call.
Only one handset (or the base unit) can be
connected to the outside line at a time.
If another handset is already using the line, you
need to wait until it has finished its call.
-
On the base station, press and hold the
key for 5 seconds
- On the handset, press / or to select
ADVANCE SET
/ / or to select
REGISTRATION
/ /
enter Master PIN
when prompted / /
WAITING
displayed / confirmation beep.
Unregister your handset
-
/ or to select
ADVANCE SET
/ / or to select
UNREGISTER
/ / enter Master PIN when prompted / /
or to select the handset number to unregister / /
confirmation beep.
Change recall time
-
/ or to select
ADVANCE SET
/ / or to select
RECALL TIME
/ / or to select
SHORT
,
MEDIUM
or
LONG
/ / confirmation beep.
Change the dial mode (dual mode dialing version only)
You should normally leave the dialling mode at its default setting of
TONE (also called MF or DTMF).
However, you can change to PULSE if necessary.
Note: If PULSE dialling is set, you can press to switch to TONE
dialling for the rest of that call.
- / or to select
ADVANCED SET
/ / or to select
DIAL MODE
/ / or to select
TONE
or
PULSE
/ /
confirmation beep.
Reset unit
-
/ or to select
ADVANCE SET
/ / or to select
RESET
/ / / confirmation beep.
www.alcatel-home.com
ATLINKS Europe, 147 avenue Paul Doumer 92500 RUEIL-MALMAISON – France
© ATLINKS 2016 - Reproduction prohibited.
The manufacturer reserves the right to modify the specifications of
its products in order to make technical improvements or comply
with new regulations.
ALCATEL and ATLINKS are registered trademarks.
The Alcatel logo and Alcatel name are trademarks of
Alcatel-Lucent and used under license by ATLINKS.
E132 / E132 Duo / Trio
E192 / E192 Duo / Trio
A/W No. : 10001557 Rev.0 (LA-EN)
Made in China
Delete all entries from the phonebook list
-
/ or to select
PHONEBOOK
/ / or to select
DELETE ALL
/ / / confirmation beep.
Set date format
-
/ or to select
CLOCK&ALARM
/ / or to select
SET FORMAT
/ / or to select
DATE FORMAT
/ /
current setting display / or to select
DD/MM
or
MM/DD
/ /
confirmation beep.
Set alarm
-
/ or to select
CLOCK&ALARM
/ / or to select
ALARM
/ / or to select
OFF
,
ON ONCE
or
ON DAILY
/ .
-
if select
ON ONCE
or
ON DAILY
, enter time (
HH-MM
) for alarm
/ or to select
AM
or
PM
if in 12 HOURS format / /
confirmation beep.
Set alarm tone
-
/ or to select
CLOCK&ALARM
/ / or to select
ALARM TONE
/ / or to select
MELODY 1
,
MELODY 2
or
MELODY 3
/ / confirmation beep.
Register your handset
IMPORTANT:
Handset registration is only necessary when you buy
extra handsets or if a handset has become faulty.
Up to 4 handsets can be registered to one base station.
The Master PIN is required before you can register or unregister
handsets.
By default, the Master PIN is 0000.
Advanced use of your telephone
Change Master PIN
The Master PIN is used for registration / unregistration of handsets.
The default Master PIN number is 0000.
Note: If you forget your PIN code, you can reset it to its default 0000
using a handset Reset.
- / or to select
ADVANCED SET
/ / or to select
CHANGE PIN
/ / enter current master pin when prompted / /
enter new
PIN
/ / confirmation beep.
Handset Tone
Set the ring volume
There are 5 ringer volume options (OFF, LEVEL 1, LEVEL 2,
LEVEL 3, LEVEL 4 and LEVEL 5). The default level is LEVEL 3.
- / or to select
PERSONAL SET
/ / or to select
HANDSET TONE
/ to select
RING VOLUME
/ / or to
the desired volume level / / confirmation beep.
Set the ring melody: 10 ring melodies
-
/ or to select
PERSONAL SET
/ / or to select
HANDSET TONE
/ / or to select
RING TONES
/ /
or to the desired melody / / confirmation beep.
Using the intercom (Duo / Trio versions)
Intercom another handset
- If only 2 registered handsets: .
- If more than 2 registered handsets: the available handset number
and * displayed / enter the handset number.
- To ring all handsets to intercom: .
Transfer an external call to another handset
During the call:
- If only 2 registered handsets: .
- If more than 2 registered handsets: the available handset number
and * displayed / enter the handset number.
- To ring all handsets to intercom: .
-
on the called handset to answer the internal call /
on
the
first handset transfer the external call to the called handset /
external call tansferred.
Note: If there is no answer from the called handset, press key
to resume the external call.
Answer an external call during intercom
- / answer the external call and end the intercom.
Note: To put the internal call on hold and answer the incoming
external call, press key.
Switch between an internal and external call
- During the call, press and hold .
Establish a three-party conference call
- During call, / enter handset number / on the called handset
to answer / long press on the first handset.
CONFERENCE
will be displayed on the screen once the
conference call is established.
The store where you bought your telephone can also provide you
with information and after - sales support.
Use handsfree (only for E192)
- To activate / desactivate handsfree : .
Adjust the earpiece volume
During a call, press or to select from VOLUME 1 to VOLUME 5.
Mute / unmute microphone
- to turn on / off the microphone.
Set time and date
Note: If you subscribe to the Caller Display service, the time and
date will be set automatically when you receive a call, but you may
still need to set the correct year.
- / or to select
CLOCK & ALARM
/ / to select
DATE / TIME
to display the last stored date / enter the current
(YY - MM - DD) / / enter the time (HH-MM) / .
Change your handset’s name
- / or to select
PERSONAL SET
/ / or to select
HANDSET NAME
/ to display the current handset name /
to delete the characters / enter the new name (maximum 10
characters) / / confirmation beep.
Make and answer calls
Make a call
- either before or after dialing your number.
- From redial list : / or / .
- From call log list*: / or / .
Note: You need to subscribe to Caller Line Identification service to
be able to see the caller’s number or name in the call log.
- From phonebook: / or / .
- From direct memories : long press on KEY 1 or KEY 2 in idle mode.
Answer and end a call
- / .
IMPORTANT NOTE: You can simply place the handset back on its
base station or charger pod to end the call.
Activate / deactivate key tone
-
/ or to select
PERSONAL SET
/ / or to select
HANDSET TONE
/ / or to select
KEY BEEP
/ / or
to select
ON
or
OFF
/ / confirmation beep.
enter direct memory menu / or to select
EDIT NUMBER
/ /
currently stored name displayed (or
ENTER NAME
if there is no
number stored) / edit or enter the name / / confirmation beep.
Set date / time format
Set time format
-
/ or to select
CLOCK&ALARM
/ / or to select
SET FORMAT
/ / to enter
TIME FORMAT
/ current setting
displayed / or to select
12 HOURS
or
24 HOURS
/ /
confirmation beep.
PLEASE READ THIS USER'S GUIDE BEFORE USING YOUR PHONE
FAVOR DE LEER TODO EL MANUAL ANTES DE UTILIZAR SU TELÉFONO
* Subject to subscription and availability of the service from the fixed line
operator.
2
1
4
6
9
3
12
5
8
10
11
7
E132 / E132 Duo / TRiO
E192 / E192 Duo / TRiO
A Displays Icons
B Displays in menu mode to confirm
your selection.
C Indicates that more options are available.
Use the UP / DOWN keys to scroll up/down.
D Displays in menu mode.
Select BACK to return to the previous menu
level. Select BACK to delete the last digit/
character entered.
Call screening
Call screening allows you to hear the caller while he is leaving
a message.
You can then decide if you want to talk to the caller directly.
HANDSET LOCATOR button
Press to page handsets.
Press and hold to start registration
procedure.
Activate / deactivate auto hang-up
-
/ or to select
PERSONAL SET
/ / or to select
AUTO HANG-UP
/ / or to select
ON
or
OFF
/ /
confiramtion beep.
C
D
A
B
